 | Chapter 39 Time and Performance |  |
| Chapter 39 Time and Performance | |
| nice | The nice command modifies the scheduling priority of time-sharing processes (for BSD and pre-V.4 releases of System V, all processes). The GNU version is on the CD-ROM (the disc's install system will only install nice if your system has the appropriate facilities). |
|---|
If you're not familiar with UNIX, you will find its definition of priority confusing - it's the opposite of what you would expect. A process with a high nice number runs at low priority, getting relatively little of the processor's attention; similarly, jobs with a low nice number run at high priority. This is why the nice number is usually called niceness: a job with a lot of niceness is very kind to the other users of your system (i.e., it runs at low priority), while a job with little niceness will hog the CPU. The term "niceness" is awkward, like the priority system itself. Unfortunately, it's the only term that is both accurate (nice numbers are used to compute priorities but are not the priorities themselves) and avoids horrible circumlocutions ("increasing the priority means lowering the priority...").
Many supposedly experienced users claim that nice has virtually no effect. Don't listen to them. As a general rule, reducing the priority of an I/O-bound job (a job that's waiting for I/O a lot of the time) won't change things very much. The system rewards jobs that spend most of their time waiting for I/O by increasing their priority. But reducing the priority of a CPU-bound process can have a significant effect. Compilations, batch typesetting programs (troff, TeX, etc.), applications that do a lot of math, and similar programs are good candidates for nice. On a moderately loaded system, I have found that nice typically makes a CPU-intensive job roughly 30 percent slower and consequently frees that much time for higher priority jobs. You can often significantly improve keyboard response by running CPU-intensive jobs at low priority.
Note that System V Release 4 has a much more complex priority system, including real-time priorities. Priorities are managed with the priocntl command. The older nice command is available for compatibility. Other UNIX implementations (including HP and Concurrent) support real-time scheduling. These implementations have their own tools for managing the scheduler.
The nice command sets a job's niceness, which is used to compute its priority. It may be one of the most non-uniform commands in the universe. There are four versions, each slightly different from the others. BSD UNIX has one nice that is built into the C shell, and another standalone version can be used by other shells. System V also has one nice that is built into the C shell and a separate standalone version.
Under BSD UNIX, you must also know about the renice(8) command (39.11); this lets you change the niceness of a job after it is running. Under System V, you can't modify a job's niceness once it has started, so there is no equivalent.
NOTE: Think carefully before you nice an interactive job like a text editor. See article 39.10.
We'll tackle the different variations of nice in order.
Under BSD UNIX, nice numbers run from -20 to 20. The -20 designation corresponds to the highest priority; 20 corresponds to the lowest. By default, UNIX assigns the nice number 0 to user-executed jobs. The lowest nice numbers (-20 to -17) are unofficially reserved for system processes. Assigning a user's job to these nice numbers can cause problems. Users can always request a higher nice number (i.e., a lower priority) for their jobs. Only the superuser (1.24) can raise a job's priority.
To submit a job at a greater niceness, precede it with the modifier nice. For example, the command:
%nice awk -f proc.awk datafile > awk.out
runs an awk command at low priority. By default, csh version of nice will submit this job with a nice level of 4. To submit a job with an arbitrary nice number, use nice one of these ways:
%nice +ncommand%nice -ncommand
where n is an integer between 0 and 20. The +n designation requests a positive nice number (low priority); -n request a negative nice number. Only a superuser may request a negative nice number.
The standalone version of nice differs from C shell nice
in that it is a separate program, not a command built in to the C shell.
You can therefore use the standalone version in any situation: within
makefiles (28.13),
when you are running the Bourne shell, etc. The principles
are the same. nice numbers run from -20 to 20, with the default
being zero. Only the syntax has been changed to confuse you. For the
standalone version, -n requests
a positive nice number (lower priority) and --n
requests a negative nice number (higher priority-superuser only).
Consider these commands:
$nice -6 awk -f proc.awk datafile > awk.out#nice --6 awk -f proc.awk datafile > awk.out
The first command runs awk with a high nice number (i.e., 6). The second command, which can be issued only by a superuser, runs awk with a low nice number (i.e., -6). If no level is specified, the default argument is -10.
System V takes a slightly different view of nice numbers. nice levels run from 0 to 39; the default is 20. The numbers are different but their meanings are the same: 39 corresponds to the lowest possible priority, and 0 is the highest. A few System V implementations support real-time submission via nice. Jobs submitted by root with extremely low nice numbers (-20 or below) allegedly get all of the CPU's time. Systems on which this works properly are very rare and usually advertise support for real-time processing. In any case, running jobs this way will destroy multiuser performance. This feature is completely different from real-time priorities in System V Release 4.
With these exceptions, the C shell version of nice is the same as its BSD cousin. To submit a job at a low priority, use the command:
%nicecommand
This increases the command's niceness by the default amount (4, the same as BSD UNIX); command will run at nice level 24. To run a job at an arbitrary priority, use one of the following commands:
%nice +ncommand%nice -ncommand
where n is an integer between 0 and 19. The +n entry requests a higher nice level (a decreased priority), while -n requests a lower nice level (a higher priority). Again, this is similar to BSD UNIX, with one important difference: n is now relative to the default nice level. That is, the command:
%nice +6